4361
Comment:
|
4257
|
Deletions are marked like this. | Additions are marked like this. |
Line 15: | Line 15: |
1. Centosの国内のミラーの状況は [[https://mirror-status.centos.org/#jp | the status of CentOS mirrors]]を参照。 | |
Line 17: | Line 16: |
2. CentOS 8 には CentOS 8 と CentOS 8-stream の2種があるが、通常の安定したサーバ向けの用途には CentOS 8 (CentOS 8.0.1905)の方を使用する。 | 1. CentOS 8 には CentOS 8 と CentOS 8-stream の2種があるが、通常の安定したサーバ向けの用途には CentOS 8 (CentOS 8.0.1905)の方を使用する。 |
Line 22: | Line 21: |
3. サーバが USB-boot に対応している場合(最近のサーバの場合)インストール用iso イメージは DVD-R に焼かずに USB 上に Bootable USB を作成した方が、高速にインストールできる。 | 2. サーバが USB-boot に対応している場合(最近のサーバの場合)インストール用iso イメージは DVD-R に焼かずに USBメモリー 上に Bootable USB を作成した方が、はるかに高速にインストールできる。 |
Line 40: | Line 39: |
配下の3つのファイル(CentOS-AppStream.repo, CentOS-Base.repo, CentOS-Extras.repo)の最初の方の baseurlをコメントアウトしてサーバを指定 | 配下の3つのファイル(CentOS-AppStream.repo, CentOS-Base.repo, CentOS-Extras.repo)の最初の方の baseurlをコメントをはずしてサーバを指定 |
Centos8インストール前のヒント
1. CentOS 8 には CentOS 8 と CentOS 8-stream の2種があるが、通常の安定したサーバ向けの用途には CentOS 8 (CentOS 8.0.1905)の方を使用する。 CentOS Stream は 開発者向けの rolling-release Linux distro である。CentOS 8のインストールには以下から dvd iso をダウンロードする。
http://ftp.riken.jp/Linux/centos/8/isos/x86_64/
2. サーバが USB-boot に対応している場合(最近のサーバの場合)インストール用iso イメージは DVD-R に焼かずに USBメモリー 上に Bootable USB を作成した方が、はるかに高速にインストールできる。 (参考)USB メモリを利用して PC に Linux (CentOS) をインストール
Centos8インストール後の初期設定
1. yum (dnf-3) レポジトリーのソースを変更(ミラーサーバを設定)
/etc/yum.repos.d/
配下の3つのファイル(CentOS-AppStream.repo, CentOS-Base.repo, CentOS-Extras.repo)の最初の方の baseurlをコメントをはずしてサーバを指定
CentOS-AppStream.repo baseurl=http://ftp.riken.jp/Linux/centos//$releasever/AppStream/$basearch/os/ CentOS-Base.repo baseurl=http://ftp.riken.jp/Linux/centos/$releasever/BaseOS/$basearch/os/ CentOS-Extras.repo baseurl=http://ftp.riken.jp/Linux/centos//$releasever/extras/$basearch/os/
と変更、yum update (dnf-3 update)を実施(初期update)
2. EPEL repository の追加
# yum install epel-release
3. 旧来のiptablesを使いたい場合、kernelのパケットフィルタを firewalld から iptables に変更
# systemctl stop firewalld.service # systemctl mask firewalld.service # yum install iptables-services # systemctl enable iptables.service # systemctl start iptables.service
4. 必要ならば SELinux を disable する
/etc/selinux/config
中で
#SELINUX=enforcing SELINUX=disabled
の変更後、reboot
5. SSHを外部に開いている場合は、パスワード認証を禁止
/etc/ssh/sshd_config
中、以下の変更
PasswordAuthentication no
を行い、sshd を再起動
6. Chronydの設定
/etc/chrony.conf
を設定。以下設定例1(外部stratum1サーバに同期):
server 133.243.238.163 iburst server 133.243.238.164 iburst server 133.243.238.243 iburst server 133.243.238.244 iburst server ntp01.sinet.ad.jp iburst server ats1.e-timing.ne.jp iburst server time.google.com iburst server ntp.jst.mfeed.ad.jp iburst
以下設定例2(外部stratum1サーバに同期している内部サーバに同期):
server ribf.riken.jp iburst server ribf00.riken.jp iburst server ribf01.riken.jp iburst server ribfsmtp1.riken.jp iburst server ribfsmtp2.riken.jp iburst
chronydサービスを有効化、起動,
以下のコマンドで時刻同期を確認
chronyc sources
7. ganglia-gmond のインストール (2019/9/27 epelにまだ ganglia-gmond はありません!)
# yum install ganglia-gmond
/etc/ganglia/gmond.conf を設定する(隣接ノードからコピー)
必要なport 8649/tcp, 8650/tcp をiptables で開ける(LAN内)
実行設定
# systemctl enable gmond # systemctl start gmond